View GP1FH500RZ_248884.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GP1FH500TZ/GP1FH500RZ
GP1FH500TZ/ GP1FH500RZ
s Features
1. Optimum height for mounting on PC (Center height:7mm) 2. Unidirectional signal transmission for plastic optical fiber cables 3. The optical receiver can be directly connectable the TTL, due to the use of OPIC 4. Compact package (height:11.1mm) with no mounting hole
Square Type Fiber Optic Transmitter/ Receiver for Personal Computers
s Outline Dimensions
13.6 3.7 7.5 9.5 6 11.1 4 7 2.54
123
(Unit : mm)
10
8.2
s Applications
1. Personal computers 2. STB 3. Digital sound cards
3.7 6.7 10.53
20.2 0.30.2
0.50.2 2.54 (9.2)
s Absolute Maximum Ratings
Parameter Supply voltage Output current (GP1FH500RZ) Input voltage (GP1FH500TZ) Operating temperature Storage temperature *1 Soldering temperature
*1 For 5s (2 times or less)
(Ta=25C)
Internal equivalent circuit GP1FH500TZ LED Driver IC GP1FH500RZ
1 3 2
Symbol Rating Unit VCC -0.5 to +7.0 V IOH 4 (Source current) mA IOL 4 (Sink current) VIN -0.5 to VCC +0.5 V Topr -20 to +70 C Tstg -30 to +80 C Tsol 260 C
Amp.
2 1 3
Amp. Amp.
OPIC light detector
1 2 3
VIN VCC GND
1 2 3
VCC GND VOUT
Unspecified tolerance:0.3mm ( ):Reference dimensions
"OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signalprocessing circuit integrated onto a single chip.
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://www.sharp.co.jp/ecg/
1.60.2 3.6 1.00.2 Amp.
7
GP1FH500TZ/GP1FH500RZ s Recommended Operating Conditions (GP1FH500TZ)
Parameter Operating supply voltage *2 Operating transfer rate
*2 NRZ signal, duty 50%
Symbol VCC T
MIN. 4.75 -
TYP. 5.0 -
MAX. 5.25 8
(Ta=25C) Unit V Mbps
s Recommended Operating Conditions (GP1FH500RZ)
Parameter Operating supply voltage *3*4 Operating transfer rate *5 Input optical power level Symbol VCC T PC MIN. 4.75 0.1 -24 TYP. 5.0 - - MAX. 5.25 8 -14.5
(Ta=25C) Unit V Mbps dBm
*3 The above operating transfer rate is the value when NRZ signal, "0101.." continuous signal of duty 50% is transmitted *4 The output (H/L level) of GP1FH500RZ are not fixed constantly when it receivers the modulating light (including DC light, no input light) less than 0.1Mbps *5 Peak emission value
s Electro-optical Characteristics (GP1FH500TZ)
Parameter Symbol p Conditions
MIN.
630
(Ta=25C, Vcc=5V) TYP. MAX. Unit
660 690
Peak emission wavelength Optical output coupling with fiber Dissipation current High level input voltage Low level input voltage LowHigh delay time HighLow delay time Pulse width distortion Jitter
PC ICC VIH VIL tpLH tpHL tw tj
- Refer to Fig.1 Refer to Fig.2 Refer to Fig.2 Refer to Fig.2 Refer to Fig.3 Refer to Fig.3 Refer to Fig.3 Refer to Fig.3
-21 -
2
- - - -25 -
-17 4 - - - - - 1
-15 10 - 0.8 100 100 +25 25
nm dBm mA V V ns ns ns ns
s Electro-optical Characteristics (GP1FH500RZ)
Parameter Symbol p Conditions
MIN. - -
2.7
(Ta=25C, Vcc=5V) TYP. MAX. Unit
700 15
Peak sensitivity wavelength Dissipation current High level output voltage Low level output voltage Rise time Fall time LowHigh delay time HighLow delay time Pulse width distortion Jitter
ICC VOH VOL tr tf tpLH tpHL tw tj
- Refer to Fig.4 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.6, PC=-14.5dBm Refer to Fig.6, PC=-24dBm
-
40
3.5
0.2 12 4
-
0.4
- - - - - -30 - -
- - - 1 -
30 30 100 100 +30 30 30
nm mA V V ns ns ns ns ns ns ns
s Mechanical Characteristics
Parameter Insertion force, withdrawal force Symbol - Conditions Initial value when a GP1C331 in used. MIN. 6 TYP. - MAX. 40 Unit N
GP1FH500TZ/GP1FH500RZ Fig.1 Measuring Method of Optical Output Coupling with Fiber
Standard optical fiber cable GP1FH500TZ Unit to be measured Vin VCC GND VCC D The optical power meter must be calibrated to have the wavelength sensitivity of 660nm (0dB=1mW) Optical power meter (Anritsu) ML93B
Note (1) VCC; 5.0V (State of operating) (2) To bundle up the standard fiber optic cable, make it into a loop with the diameter D=10cm or more (The standard fiber optic cable will be specified elsewhere.)
Fig.2 Measuring Method of Intput Voltage and Supply Current
Standard fiber optic cable GP1FH500TZ Unit to be measured VIN VCC Icc VIN VCC GND
D
Optical power meter (Anritsu) ML93B The optical power meter must be calibrated to have the wavelength sensitivity of 660nm (0dB=1mW)
Input conditions and judgement method Conditions VIN=2.0V or more VIN=0.8V or less Judgement method -21PC-15dBm, ICC=10mA or less PC-36dBm, ICC=10mA or less
Note VCC=5.0V (State of operating)
GP1FH500TZ/GP1FH500RZ Fig.3 Measuring Method of Pulse Response and Jitter
Standard fiber optic cable GP1FH500TZ Unit to be measured VIN VCC GND VCC Input 1 10 0 Input signal 3Mbps biphase mark PRBS signal Oscilloscope CH1 CH2 Tektronix 7834 or 7934 type Trigger;CH1 Storage mode Standard receiver Output signal
Input signal tPLH tPHL
50%
Standard receiver output
tjr tjf
50%
Parameter
Symbol
Conditions
LowHigh delay time HighLow delay time Pulse width distortion LowHigh jitter HighLow jitter
tpLH tpHL tw tjr tjf
Refer to the above mentioned prescription Refer to the above mentioned prescription tw=tpHL-tpHL Set the trigger on the rise of input signal to measure the jitter of the rise of output Set the trigger on the fall of input signal to measure the jitter of the fall of output
Notes (1) The waveform write time shall be 4s. But do not allow the waveform to be distorted by increasing the brightness too much (2) VCC=5.0V (State of operating) (3) The probe for the oscilloscope must be more than 1M and less than 10pF
Fig.4 Supply Current
Supply voltage Fiber coupling light output Standard transmitter input signal Input conditions VCC=5.0V PC=-14.5dBm 6Mbps NRZ, Duty 50% or 3Mbps biphase mark PRBS signal
Fiber optic cable Standard transmitter Vin VCC GND VCC A Am meter VCC GP1FH500RZ Unit to be measured GND Vout
Measuring method Measured on an ammeter (DC average amperage)
5V Input
GP1FH500TZ/GP1FH500RZ Fig.5 Measuring Method of Output Voltage and Pulse Response
Fiber optic cable Standard transmitter VCC VIN VCC GND VCC Input 5V RSO RSI GP1FH500RZ Unit to be measured GND VOUT
6Mbps NRZ, Duty 50%
CH1
CH2
Tektronix 7834 or 7934 type Oscilloscope
Test item Test item Low High pulse delay time High Low pulse delay time Rise time Fall time Pulse width distortion tw=tpHL-tpLH High level output voltage Low level output voltage
Notes (1) (2) (3) (4) (5)
Symbol tpLH tpHL tr tf tw VOH VOL
Standard transmitter Input signal (CH1)
50%
tr VOH GP1FH500RZ Output signal (CH2) VOL
tf 90% 50% 10%
VCC=5.0V (State of operating) The fiber coupling light output set at -14.5dBm/-24dBm The probe for the oscilloscope must be more than 1M and less than 10pF RSI, RSO:Standard load resistance (RSI:3.3k, RSO:2.2k) The output (H/L level) of GP1FH500RZ are not fixed constantly when it receives the modulating light (including DC light, no input light) less than 0.1Mbps
tpLH
tpHL
GP1FH500TZ/GP1FH500RZ Fig.6 Measuring Method of Jitter
Fiber optic cable Standard transmitter VCC GP1FH500RZ Unit to be measured GND VOUT
VIN
VCC
GND
VCC 5V
RSO RSi
Oscilloscope Input CH1 Tektronix 7834 or 7934 type Trigger : CH1 Storage mode Sweep : AUTO/NORM
CH2 Input signal 3Mbps biphase, PRBS signal
Test item Test item Symbol Jitter Jitter tj tj
Test condition Set the trigger on the rise of input signal to measure the jitter of the rise of output Set the trigger on the fall of input signal to measure the jitter of the fall of output
Input signal
50%
Notes (1) The fiber coupling light output set at -14.5dBm/-24dBm (2) RSI, RSO:Standard load resistance (RSI:3.3k, RSO:2.2k) (3) The waveform write time shall be 3s. But do not allow the waveform to be distorted by increasing the brightness too much (4) VCC=5.0V (State of operating) (5) The probe for the oscilloscope must be more than 1M and less than 10pF
GP1FH500RZ output
50%
tj
tj
Application Circuits
NOTICE
qThe circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. qContact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. qObserve the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). qContact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. qIf the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. qThis publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. qContact and consult with a SHARP representative if there are any questions about the contents of this publication.
115

▲Up To Search▲

Price & Availability of GP1FH500RZ

	To Download GP1FH500RZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .